Fundamental Plumber Guide for Installing a Bathtub
Fundamental Plumber Guide for Installing a Bathtub
Blog Article
We have uncovered this great article about How to Install a Bathtub down the page on the web and concluded it made perfect sense to discuss it with you on this site.
Mounting a bath tub isn't precisely rocket science, yet it does need solid plumbing, woodworking, as well as in some cases, tiling abilities. Changing an old bathtub with a brand-new one is also a reasonably challenging task. If the old tub is conveniently easily accessible, the project can move speedily; if you have to open a wall surface to eliminate the old tub and also place the new bathtub, the task is a lot harder. In either situation, the job is within a residence handyman's skills, although you will certainly require a helper to leave the old bathtub and embeded in the new one. See to it you have certified on your own for the job as well as fit attempting it. Instead of working with a service provider to take over a halfway-completed job, it is far better to consider employing one prior to you begin. Chances are you might require an expert plumber to make tube connections.
This write-up will certainly help you install a brand-new bathtub in your bathroom if you have actually already bought a brand-new tub and also don't require to alter the setup of your previous water system pipelines.
Your tools as well as material checklist must comprise the following:
Getting ready for the Installment
To start with, the sustaining framework supplied with the bathroom ought to be fitted (if called for) according to the maker's instructions. Next off, fit the taps or mixer to the bathtub. When suitable the faucet block, it is necessary to ensure that if the faucet features a plastic washer, it is fitted between the bath and the taps. On a plastic bath, it is also practical to fit a sustaining plate under the faucets system to prevent pressure on the tub.
Fit the versatile faucet ports to the bottom of both taps making use of 2 nuts as well as olives (sometimes provided with the tub). Fit the plug-hole electrical outlet by smearing mastic filler round the sink outlet hole, and after that pass the electrical outlet via the hole in the bathroom. Make use of the nut provided by the producer to fit the plug-hole. Check out the plug-hole electrical outlet for an inlet on the side for the overflow pipe.
Next off, fit the end of the flexible overflow pipe to the overflow electrical outlet. Afterwards, screw the pipe to the overflow face which should be fitted inside the bath. Make sure you make use of all of the supplied washing machines.
Link the trap to the bottom of the waste electrical outlet on the tub by winding the string of the waste electrical outlet with silicone mastic or PTFE tape, and also screw on the trap to the outlet. Link the bottom of the overflow tube in a similar manner.The bath should currently prepare to be suited its final position.
Removing Old Taps
If you require to replace old taps with brand-new ones as a part of your installment, after that the first thing you ought to do is disconnect the water supply. After doing so, activate the taps to drain pipes any type of water staying in the system. The process of getting rid of the existing taps can be quite bothersome due to the limited access that is often the situation.
Use a basin wrench (crowsfoot spanner) or a faucet tool to reverse the nut that links the supply pipelines to the faucets. Have a fabric ready for the continuing to be water that will come from the pipes. As soon as the supply pipelines have been gotten rid of, utilize the very same tool to loosen up the nut that holds the faucets onto the bath/basin. You will certainly need to stop the solitary faucets from transforming throughout this process. When the taps have been removed, the holes in the bath/basin will certainly need to be cleaned up of any old securing compound.
Before carrying on to fit the new taps, compare the pipeline links on the old taps to the brand-new faucets. If the old taps are longer than the brand-new taps, after that a shank adapter is required for the new faucets to fit.
Setting up the Tub
Utilizing the two wood boards under its feet, put the bath tub in the needed setting. The wood boards are handy in evenly spreading out the weight of the tub over the location of the boards instead of focusing all the weight onto four little points.
The next objective is to ensure that the tub is leveled all round. This can be achieved by examining the level and also changing the feet on the tub till the level checks out degree.
To set up faucets, fit all-time low of the outermost adaptable faucet connector to the suitable supply pipe by making a compression join; after that do the same for the various other tap.
Turn on the supply of water and check all joints as well as brand-new pipework for leaks as well as tighten them if necessary. Fill up the bath tub and likewise examine the overflow outlet as well as the regular outlet for leaks.
Lastly, take care of the bath paneling as explained in the manufacturer's user's manual. Tiling and also sealing around the tub needs to wait till the bath tub has been made use of a minimum of when as this will certainly resolve it right into its final position.
Fitting New Taps
If the tails of the new taps are plastic, after that you will certainly require a plastic port to stop damages to the string. One end of the port fits on the plastic tail of the tap and the other end gives a connection to the current supply pipelines.
If you require to fit a monobloc, after that you will certainly call for lowering couplers, which links the 10mm pipe of the monobloc to the standard 15mm supply pipeline.
Next off, position the faucet in the mounting opening in the bath/basin guaranteeing that the washing machines are in place in between the tap and the sink. Protect the faucet in position with the manufacturer offered backnut. When the faucet is firmly in place, the supply pipes can be linked to the tails of the taps. The faucets can either be linked by utilizing corrugated copper piping or with regular faucet adapters. The previous kind needs to be attached to the faucet finishes initially, tightening up just by hand. The supply pipes can later be connected to the other end. Tighten both ends with a spanner after both ends have actually been attached.
Tiling Around the Tub
In the area where the bath fulfills the floor tile, it is needed to seal the joins with a silicone rubber caulking. This is very important as the fitting can move enough to fracture an inflexible seal, causing the water to permeate the wall in between the bath as well as the tiling, leading to problems with moisture and feasible leaks to the ceiling listed below.
You can choose from a range of coloured sealants to blend in your components and installations. They are marketed in tubes and cartridges, as well as can sealing spaces approximately a size of 3mm (1/8 inch). If you have a larger space to fill up, you can load it with twists of soaked newspaper or soft rope. Keep in mind to constantly load the bathtub with water before sealing, to enable the motion experienced when the bathtub remains in usage. The sealer can split rather very early if you do not take into account this movement prior to securing.
Conversely, ceramic coving or quadrant tiles can be made use of to border the bathroom or shower tray. Plastic strips of coving, which are easy to use and also reduce to dimension, are also easily available on the market. It is recommended to fit the floor tiles using waterproof or water resistant sticky and grout.
A Step-by-Step Guide to Installing a Bathtub
Is your bathtub looking a bit dated lately? Believe it or not, installing a new one is a project you can do yourself. Whether your bathtub is broken or doesn’t fit in with your current bathroom’s design, you can fix it without having to hire a contractor or paying labour costs.
But, beyond saving money, there are other benefits of installing your own bathtub. When you do this project yourself, you can customise every step of the process. You can also make sure the finished product looks exactly the way you want it to.
This DIY project is quite involved, but by doing some research, preparing your bathroom and using the right equipment, it is definitely one you can take on. This guide will help you understand the technical procedures behind installing a new bathtub.
Remove the Existing Bathtub
To remove the old bathtub, you will need to turn the water supply off before you start any work. After you turn the water off, there will likely still be some water left in your plumbing system, which you can remove by turning on a faucet below the level of the bathtub. Once the water stops running, you are ready to start working.
The easiest way to remove the tub is to remove the faucet, handles and other piping and then pull the tub out from the wall. If this doesn’t work in your situation, you will need to remove part of the wall, remove the piping and then slide the tub out.
Choose the Right Bathtub
The ideal way to replace your bathtub is to find one that has the exact dimensions and has the drain and faucet on the same side as your old one. This way, it will fit in the same place and you won’t have to change the piping system in your bathroom. Choose a tub that matches your home’s decor and fits with the style of the bathroom.
Install the Plumbing and Ledger Board
You can purchase a tub drain kit at a hardware store which will have all the pieces you will need for your new tub’s plumbing. Follow the instructions that came with the kit to install the plumbing in the new tub and then take measurements to make sure the plumbing in the tub will align with the plumbing in your bathroom. If it doesn’t, now is the time to make necessary adjustments.
Some bathtubs need a ledger board that is installed on the wall behind the tub to help support it. If your new bathtub requires one, the directions that came with it will tell you how high it should be installed. If your old bathtub had a ledger board, and it is still in good condition, you can adjust its height to match the new bathtub.
Install the Bathtub
When the plumbing and ledger board are ready, you can install the new bathtub. Carefully lower it into the space, being careful not to damage the tub, wall, plumbing or ledger board. Since bathtubs are very heavy and you will need to line the tub up exactly, it is wise to have someone help you with this step.
Once the tub is in place, it needs to be perfectly level, so use a bubble level instead of estimating how level the tub is. Put the level on the top edge of the tub, not the bottom on the inside, since many tubs are designed with a sloped bottom.
If the bathtub isn’t level, adjust the ledger board and shift the tub until it is. When it is level, use screws to attach the tub to the wall studs. Most bathtubs have pre-drilled holes in the upper flange, so use these but do not over tighten the screws.
Hook up the Plumbing
Now that the bathtub is installed, it needs to be attached to your plumbing system. First, install the shoe fitting under the tub and drain pipe, then the overflow pipe and then the drain flange. Your tub plumbing kit will include specific instructions on how to install these pieces.
Install the Bathtub Surround
A bathtub surround will protect the walls around the tub from water damage and can give your new bathtub a more finished look. To install one, make sure the wall is completely clean and dry so that the adhesive will be able to hold the surround securely. Then, measure the surround and mark the same dimensions on the wall above the tub.
Following the directions that came with the surround adhesive, apply it to the wall. Press the surround against the wall on top of the adhesive and then pull it away for about three minutes to activate the adhesive, then apply the surround again. Keep in mind that this is the most common way to use an adhesive, but you should check the instructions on the package for any special steps.
If there is any excessive adhesive around the sides of the surround, you can use mineral spirits to remove it. Then use masking tape to hold the surround panels in place until the adhesive is dry. Using silicone, seal all the cracks between the surround panels and the gap between the bottom of the panels and the top of the bathtub.
If you want to install tile above your bathtub, instead of a bathtub surround, the process will be very similar. But, you will need to measure and cut tiles and install each one individually, using tile spacers to make sure they are evenly spaced. You will then use grout to fill in the spaces between the tiles.
https://www.hss.com/blog/bathroom/a-step-by-step-guide-to-installing-a-bathtub/
We are very fascinated with How to Install a Bathtub Yourself and I really hope you enjoyed reading my article. Are you aware of someone else who is fascinated by the subject? Do not hesitate to share it. Thank you so much for taking the time to read it.
We're ready, are you? Report this page